发表了主题帖： ZCC2601-带EN脚 60V/150 mA超低静态电流LDO

Describe The ZCC2601 ultra-low quiescent current regulator features low dropout voltage and low current in the standby mode. With less than 5μA quiescent current at no load, the ZCC2601 is ideally suited for standby miZCCo-control-unit systems, especially for always-on applications like E-meters, fire alarms, smoke detectors and other battery operated systems. The ZCC2601 retains all of the features that are common to low dropout regulators including a low dropout PMOS pass device, short circuit protection, and thermal shutdown.  The ZCC2601 has a 65-V maximum operating voltage limit, a -40°C to 125°C operating temperature range, and ±2% output voltage tolerance. Features  ⚫ VIN Range up to 60V  ⚫ Output Voltage Tolerances of ±2%  ⚫ Output Current of 150 mA  ⚫ Ultra Low Quiescent Current (IQ = 2.8 μA)  ⚫ Dropout Voltage Typically 1300 mV at IOUT = 100 mA  ⚫ Internal Thermal Overload Protection  Applications  ⚫ Internal Short-Circuit Current Limit Describe  ⚫ Ceramic Capacitor Stable ⚫ E-meters, Water Meters and Gas Meters ⚫ Fire Alarm, Smoke Detector ⚫ Appliances and White Goods ​

发表了主题帖： ZCC5400 -四组配对电阻网络，替代lt5400

描述：  ZCC5400 是一个四电阻网络，具有出色的在整个温度范围内匹配规格。配置 ZCC5400 时也指定了匹配在差分放大器中。此增强的匹配规范保证 CMRR 性能 提高 2 倍与独立匹配的电阻器相比。所有四个电阻器都可以独立访问和偏置， 使 ZCC5400 成为任何可以从匹配电阻器中受益的应用。这些电阻网络提供精确 的比率稳定性高精度差分放大器所需的电压参考和桥接电路。 ZCC5400 采用节省空间的 8 针 MSOP 包装，并在以下温度范围内指定–55°C 至 150°C。 性能： ● 完美匹配  ● A 级：0.01%匹配  ● B 级：0.025%匹配  ● 0.2ppm/°C 匹配温度漂移  ● ±75V 工作电压（±80V 绝对最大值）  ● 8ppm/°C 绝对电阻值温度漂移  ● 长期稳定性：2000 小时时<2ppm  ● –55°C 至 150°C 工作温度  ● 8 导联 MSOP 封装 应用： ● 差分放大器 ● 参考分频器 ● 精度求和/减法

发表了主题帖： ZCC9159-带EN 7V/300mA 超低功耗高速 LDO

功能描述  ZCC9195是一款超低功耗并具有快速响应、关断快速放电功能的高速LDO。静态电流低至 0.8uA，输出电流最大为300mA。 ZCC9195具有输出过流保护、输出短路保护、温度保护等功能，确保芯片在异常工作条件 下不会损坏。  ZCC9195只需要1uF的陶瓷电容即可保证电压稳定输出, 其内部精密的电压基准和反馈回 路，可使电路在输入电压、负载、工艺和温度波动的情况下，确保±1%的输出电压精度。 ZCC9195 工作温度范围为–40°C ~ +125°C，封装形式为 SOT23-3L，SOT23-5L, DFN1x1-4L。 特性   • 宽输入电压：2V to 5.5V  • 最大500mA输出电流  • 输出电压：3.3/3.0/2.8/2.5/1.8/1.5/1.2/1.0V。其他输出电压或输出ADJ可调，需定制 • 高输出精度：±1%  • 超低功耗：0.8µA@typ   • 超低压差：220mV @200mA Load /VOUT=3.3V  • 短路保护电流：100mA  • 优秀的线性/负载特性 • 线性调整率：0.05% typical • 高PSRR：70dB@1KHZ   • 封装形式：SOT23-3L，SOT23-5L, DFN1x1-4L

发表了主题帖： ZCC5400 -四组配对电阻网络，替代lt5400

描述：  ZCC5400 是一个四电阻网络，具有出色的在整个温度范围内匹配规格。配置 ZCC5400 时也指定了匹配在差分放大器中。此增强的匹配规范保证 CMRR 性能 提高 2 倍与独立匹配的电阻器相比。所有四个电阻器都可以独立访问和偏置， 使 ZCC5400 成为任何可以从匹配电阻器中受益的应用。这些电阻网络提供精确 的比率稳定性高精度差分放大器所需的电压参考和桥接电路。 ZCC5400 采用节省空间的 8 针 MSOP 包装，并在以下温度范围内指定–55°C 至 150°C。 性能： ● 完美匹配  ● A 级：0.01%匹配  ● B 级：0.025%匹配  ● 0.2ppm/°C 匹配温度漂移  ● ±75V 工作电压（±80V 绝对最大值）  ● 8ppm/°C 绝对电阻值温度漂移  ● 长期稳定性：2000 小时时<2ppm  ● –55°C 至 150°C 工作温度  ● 8 导联 MSOP 封装 应用： ● 差分放大器 ● 参考分频器 ● 精度求和/减法  

发表了主题帖： ZCC2601-带EN脚 60V/150 mA超低静态电流LDO

Describe The ZCC2601 ultra-low quiescent current regulator features low dropout voltage and low current in the standby mode. With less than 5μA quiescent current at no load, the ZCC2601 is ideally suited for standby miZCCo-control-unit systems, especially for always-on applications like E-meters, fire alarms, smoke detectors and other battery operated systems. The ZCC2601 retains all of the features that are common to low dropout regulators including a low dropout PMOS pass device, short circuit protection, and thermal shutdown.  The ZCC2601 has a 65-V maximum operating voltage limit, a -40°C to 125°C operating temperature range, and ±2% output voltage tolerance. Features  ⚫ VIN Range up to 60V  ⚫ Output Voltage Tolerances of ±2%  ⚫ Output Current of 150 mA  ⚫ Ultra Low Quiescent Current (IQ = 2.8 μA)  ⚫ Dropout Voltage Typically 1300 mV at IOUT = 100 mA  ⚫ Internal Thermal Overload Protection  Applications  ⚫ Internal Short-Circuit Current Limit Describe  ⚫ Ceramic Capacitor Stable ⚫ E-meters, Water Meters and Gas Meters ⚫ Fire Alarm, Smoke Detector ⚫ Appliances and White Goods ​

发表了主题帖： ZCC2601-带EN脚 60V/150 mA超低静态电流LDO

发表了主题帖： ZCC1923_替代BOS1921

FEATURES • High-Voltage Low Power Piezo Driver  * Drive 100nF at 190VPP and 250Hz with 490mW * Drives Capacitive Loads up to 1000nF * Energy Recovery o Differential Output  * Small Solution Footprint, QFN & WLCSP  • Low Quiescent Current: SHUTDOWN; SLEEP; IDLE; IDLE mode Current only 90uA  • Multiple operating modes: AUTOPLAY; SENSEPLAY; DIRECTPLAY; FIFOPLAY; SRAMPLAY  * State Retention in SLEEP Mode  • Fast Start Up Time less than 200 µs  • Multi-Actuator Synchronization; address selection; Power-on-Reset  • ESD verification pass, latch up verification pass DESCRIPTION  The ZCC1923 is a single-chip piezo actuator driver with energy recovery, based on Analogwin’s patented technology. It can drive actuators with waveforms up to 190 Vpk-pk while operating from a 2.3 to 5.5 V supply voltage. Its low power and small size make it ideal for a variety of applications requiring minimal power consumption. The CC1923 features high-resolution piezo sensing capabilities allowing haptic feedback to be automatically played when detection conditions are met.  The ZCC1923 differential driver achieves low distortion waveforms and quiet actuator operation. All settings are adjustable through the digital front end to reduce the BOM. Data and configuration parameters are easily communicated to the ZCC1923 through its two wire I2C interface. A flexible deep FIFO enables the streaming of digital waveform data for playback or the transmission of burst data for more bandwidth efficiency. The CC1923 also integrates 1.5 kB of RAM waveform memory to generate HD haptic waveforms with minimal communication bandwidth. A dedicated SYNC pin can synchronize multiple ZCC1923 controllers to simultaneously drive multiple actuators within 2µs. In addition to SYNC synchronization, ZCC1923 can also support CLK_SYNC synchronization. This function synchronizes the clock CLK, and multiple chips share the same CLK. With a typical start-up time of less than 200µs, the CC1923 latency is negligible in most systems.  Various safety systems protect the ZCC1923 from damage in case of a fault.  APPLICATIONS • Mobile Phones and Tablets • Portable Computers, Keyboards and Mice  • Gaming Controllers, Wearables • Electronic Cooling  

发表了主题帖： ZCC5143-3.5V 至 65V 双路同步降压芯片替代LM5143

Descriptions The ZCC5143 is a 65V synchronous step-down DC/DC controller for high current single or dual outputs. The device features an interleaved, stackable peak current mode control architecture for simple loop compensation, fast transient response, excellent load and line regulation, and precise current sharing through parallel phasing for high output currents. 65ns of ultra-short on-time for the high-side switch facilitates large buck ratios and supports direct buck conversion from 12V, 24V, or 48V automotive inputs to lower voltage rails, reducing system complexity and solution cost. The can continue to operate at nearly 100% duty cycle as needed even when the input voltage drops abruptly to 3.5V. Ultra-high efficiency is achieved by Using an inductor DCR to detect the current, and a shunt resistor can be used to detect it with high accuracy. 15uA no-load quiescent current and regulated output voltage extends the operating runtime of battery-powered systems. The can be powered by the output of a switching regulator or other available power sources. By utilizing the output of a switching regulator or other available power supply to power the , lower input quiescent current and power loss can be achieved.  Features   VIN input voltage range: +3.5V ~ +65V   1% accuracy, 3.3V/5V fixed or 0.6V to 55V adjustable output voltage   Shutdown Mode Current: 4µA (Typ.)   No-load standby current: 15 µA (Typ.)   Dual channel or single output multi-phase  65ns tON(min) for high VIN/VOUT ratio   60ns tOFF(min) for low voltage drop   Hiccup mode over-current protection  VCC, VDDA and Gate Drive UVLO Protection   Thermal shutdown protection with hysteresis  Adaptive Gate Driver Controlled by Voltage Slew Rate   Switching frequency range of 100kHz to 2.2MHz   Optional diode emulation or FPWM   VQFNP6X6-40 package Applications  Automotive Electronic Systems   Advanced Driver Assistance System(ADAS)  Infotainment & Instrumentation Systems

发表了主题帖： ZCC5090EA 替代CS5090EA ,5V升压充电管理芯片

概要 ZCC5090EA是一款5V输入，最大1.5A充电电流，支 持双 节 锂 电 池 串 联 应 用 的 升 压 充 电 管 理 IC 。ZCC5090EA集成功率MOS，采用异步开关架构， 使其在应用时仅需极少的外围器件，可有效减少整体 方案尺寸，降低BOM成本。ZCC5090EA的升压开关 充电转换器的工作频率为500KHz，转换效率为90%。 ZCC5090EA内置四个环路来控制充电过程，分别为 恒流（CC）环路、恒压（CV）环路、芯片温度调节环路、可智能调节充电电流，防止拉垮适配器输出， 并匹配所有适配器的输入自适应环路。 ZCC5090EA集成30V OVP功能，输入端口能够稳定 可靠承受30V以内的耐压冲击，并在输入超过6V时停 止充 电，非 常 适 用 于TY P E - C接 口 的 应 用。同 时 芯 片BAT输出端口耐压30V，极大提高了系统的可靠性。 ZCC5090EA提供了纤小的ESOP8L封装类型供客户 选择，其额定的工作温度范围为-40℃至85℃。 描述 *USB 5V输入异步开关升压充电，集成30V OVP功能 *工作电压3.6~6V，BAT端耐压30V，内部集成高压晶体管 *最大1.5A充电电流，充电电流外部电阻可调 *NTC功能，与使能功能复用 *升压充电效率90% *自动调节输入电流，匹配所有适配器 *支持LED充电状态指示 *500KHz开关频率，内置频率抖动功能 *输出过压，短路保护 *输入过压保护 *IC过温保护，IC温度自适应调节功能 *管脚兼容ZCC5090E  * ESD 2KV 封装 ESOP8L 应用  蓝牙音箱 电子烟 对讲机 POS机  锂电电池包 玩具

发表了主题帖： ZCC75XXH-40V/150mA高压低功耗线性稳压器替代HT75XX

功能描述  ZCC75XXH是一款高压低功耗线性稳压器，静态电流低至2.5uA，输出电流最大为150mA。该系列产品 采用先进的CMOS工艺和高压PMOSFET，具有快速启动、高输出电压精度等特点。只需要1uF 的陶瓷电容即可保证电压稳定输出, 其内部精密的电压基准和反馈回路，可使电路在输入电压、负载、工艺和温度波动的情况下，确保±1%的输出电压精度。工作温度范围–40°C ~ +125°C，封装形式为SOT89-3 ， SOT23-3L。 特性 • 宽输入电压：2V to 40V • 最大150mA输出电流 • 超低功耗：2.5µA@typ • 超低压差：650mV at 150mA Load @VOUT=5V  • 短路保护电流：60mA  • 优秀的线性/负载特性 • 线性调整率：0.05% typical  • 封装形式：SOT89-3，SOT23-3L ​ 合作洽谈/样品申请：402572194（QQ） 邮箱：gaomaobing@zcc-china.net  

发表了主题帖： ZCC5143-3.5V 至 65V 双路同步降压芯片替代LM5143

Descriptions The ZCC5143 is a 65V synchronous step-down DC/DC controller for high current single or dual outputs. The device features an interleaved, stackable peak current mode control architecture for simple loop compensation, fast transient response, excellent load and line regulation, and precise current sharing through parallel phasing for high output currents. 65ns of ultra-short on-time for the high-side switch facilitates large buck ratios and supports direct buck conversion from 12V, 24V, or 48V automotive inputs to lower voltage rails, reducing system complexity and solution cost. The can continue to operate at nearly 100% duty cycle as needed even when the input voltage drops abruptly to 3.5V. Ultra-high efficiency is achieved by Using an inductor DCR to detect the current, and a shunt resistor can be used to detect it with high accuracy. 15uA no-load quiescent current and regulated output voltage extends the operating runtime of battery-powered systems. The can be powered by the output of a switching regulator or other available power sources. By utilizing the output of a switching regulator or other available power supply to power the , lower input quiescent current and power loss can be achieved.  Features   VIN input voltage range: +3.5V ~ +65V   1% accuracy, 3.3V/5V fixed or 0.6V to 55V adjustable output voltage   Shutdown Mode Current: 4µA (Typ.)   No-load standby current: 15 µA (Typ.)   Dual channel or single output multi-phase  65ns tON(min) for high VIN/VOUT ratio   60ns tOFF(min) for low voltage drop   Hiccup mode over-current protection  VCC, VDDA and Gate Drive UVLO Protection   Thermal shutdown protection with hysteresis  Adaptive Gate Driver Controlled by Voltage Slew Rate   Switching frequency range of 100kHz to 2.2MHz   Optional diode emulation or FPWM   VQFNP6X6-40 package Applications  Automotive Electronic Systems   Advanced Driver Assistance System(ADAS)  Infotainment & Instrumentation Systems

发表了主题帖： ZCC7008B-23V 8A同步降压 替代RT6258B

3.3V/8A Synchronous Step-down Converter The ZCC7008B operates at high efficiency over a wideoutput current load range with fixed 3.3V output voltageand capable of delivering 8A load current. lt supports awide range input voltage from 4.5V to 23V.AdaptiveConstant-On-Time (COT) control mode provides fasttransient response, eases loop stabilization, andoperates with a low-cost electrolytic capacitorZCC7008B also integrate a 100mA LDO and bypassswitch for efficiency improving.ZCC7008B provides complete enable control, under/overvoltage protect, short circuit protect, valley current limit,thermal shutdown function features.ZCC7008B provides compact solution for TCON powersystem. Features 4.5V ~ 23V Input Voltage Range Fixed 3.3V output voltage Supports 8-A continuous output current Integrated 20mQ High side FET and 10m0 low side FET3.3V LDO capable ofsourcing 100mA Internal +1% reference voltage at 25°C Integrated bypass switch, typical Ron is 1.50 Internal 0.6ms soft-start Max switching frequency up to 500kHz fast transient response with COT control mode Power good indicator Ultrasonic Mode Integrated protections for Uv, Ov, OT, and OCP40°C to +150°C operating junction temperature AQFN3X3-12 FC Package Applications Notebook Computers Notebook, Tablet Computers General power supply for 3.3V output

发表了主题帖： 2.0V~5.5V输入电压，1µA超低静态电流同步升压芯片-ZCC2116TSL替代TLV61070

特性  ❖ 无开关时，1µA 超低静态电流 ❖ 可调输出电压范围：2.0V~5.5V ❖ 可选择的固定输出电压版本 5.1V/3.6V/3.3V/3.0V  ❖ 2% 反馈电压精度 (25℃)  ❖ 效率高达 95%  ❖ 关断期间真正实现断开  ❖ 过流保护功能  ❖ 过温保护功能 ❖ 输出防反灌保护  ❖ 内置软起动补偿 ❖ 1.2MHz 固定开关频率 ❖ SOT23-6 封装 描述  ZCC2116TSL 器件是一种具有超低静态电 流的高效同步升压转换器.该器件专为多种电池 供电的产品而设计，并且在轻载条件下仅消耗 1µA静态电流，轻载条件下的高效运行对于延长 电池寿命至关重要。该器件在 20µA 的负载下， 可实现高达 80%的效率。对于 2.2V 转换为 3.6V 的应用，在 200 mA 负载下，它可实现高达 92% 的效率；4.2V 转换为 5.1V 的应用，在 500 mA 负载下，它可实现高达 95%的效率。具有真关断 功能，在关闭和输出短路条件下，将输出与输入断开。  ZCC2116TSL 有 5.1V/3.6V/3.3V/3.0V 固定 输出电压版本，确保 FB 引脚浮置，不能连接 到任何设备。  同时具有过流保护、过温保护、输出短路保 护功能，确保器件安全运行。 应用范围 ❖ 移动设备、平板 ❖ 智能手机  ❖ 蓝牙应用  ❖ 电池供电系统 ​合作洽谈/样品申请：402572194（QQ） 邮箱：gaomaobing@zcc-china.net  

发表了主题帖： ZCC7008B-23V 8A同步降压 替代RT6258B

3.3V/8A Synchronous Step-down Converter The ZCC7008B operates at high efficiency over a wideoutput current load range with fixed 3.3V output voltageand capable of delivering 8A load current. lt supports awide range input voltage from 4.5V to 23V.AdaptiveConstant-On-Time (COT) control mode provides fasttransient response, eases loop stabilization, andoperates with a low-cost electrolytic capacitorZCC7008B also integrate a 100mA LDO and bypassswitch for efficiency improving.ZCC7008B provides complete enable control, under/overvoltage protect, short circuit protect, valley current limit,thermal shutdown function features.ZCC7008B provides compact solution for TCON powersystem. Features 4.5V ~ 23V Input Voltage Range Fixed 3.3V output voltage Supports 8-A continuous output current Integrated 20mQ High side FET and 10m0 low side FET3.3V LDO capable ofsourcing 100mA Internal +1% reference voltage at 25°C Integrated bypass switch, typical Ron is 1.50 Internal 0.6ms soft-start Max switching frequency up to 500kHz fast transient response with COT control mode Power good indicator Ultrasonic Mode Integrated protections for Uv, Ov, OT, and OCP40°C to +150°C operating junction temperature AQFN3X3-12 FC Package Applications Notebook Computers Notebook, Tablet Computers General power supply for 3.3V output

发表了主题帖： ZCC5143-3.5V 至 65V 双路同步降压芯片替代LM5143

Descriptions The ZCC5143 is a 65V synchronous step-down DC/DC controller for high current single or dual outputs. The device features an interleaved, stackable peak current mode control architecture for simple loop compensation, fast transient response, excellent load and line regulation, and precise current sharing through parallel phasing for high output currents. 65ns of ultra-short on-time for the high-side switch facilitates large buck ratios and supports direct buck conversion from 12V, 24V, or 48V automotive inputs to lower voltage rails, reducing system complexity and solution cost. The can continue to operate at nearly 100% duty cycle as needed even when the input voltage drops abruptly to 3.5V. Ultra-high efficiency is achieved by Using an inductor DCR to detect the current, and a shunt resistor can be used to detect it with high accuracy. 15uA no-load quiescent current and regulated output voltage extends the operating runtime of battery-powered systems. The can be powered by the output of a switching regulator or other available power sources. By utilizing the output of a switching regulator or other available power supply to power the , lower input quiescent current and power loss can be achieved.  Features   VIN input voltage range: +3.5V ~ +65V   1% accuracy, 3.3V/5V fixed or 0.6V to 55V adjustable output voltage   Shutdown Mode Current: 4µA (Typ.)   No-load standby current: 15 µA (Typ.)   Dual channel or single output multi-phase  65ns tON(min) for high VIN/VOUT ratio   60ns tOFF(min) for low voltage drop   Hiccup mode over-current protection  VCC, VDDA and Gate Drive UVLO Protection   Thermal shutdown protection with hysteresis  Adaptive Gate Driver Controlled by Voltage Slew Rate   Switching frequency range of 100kHz to 2.2MHz   Optional diode emulation or FPWM   VQFNP6X6-40 package Applications  Automotive Electronic Systems   Advanced Driver Assistance System(ADAS)  Infotainment & Instrumentation Systems

发表了主题帖： ZCC7008B-23V 8A同步降压 替代RT6258B

3.3V/8A Synchronous Step-down Converter The ZCC7008B operates at high efficiency over a wideoutput current load range with fixed 3.3V output voltageand capable of delivering 8A load current. lt supports awide range input voltage from 4.5V to 23V.AdaptiveConstant-On-Time (COT) control mode provides fasttransient response, eases loop stabilization, andoperates with a low-cost electrolytic capacitorZCC7008B also integrate a 100mA LDO and bypassswitch for efficiency improving.ZCC7008B provides complete enable control, under/overvoltage protect, short circuit protect, valley current limit,thermal shutdown function features.ZCC7008B provides compact solution for TCON powersystem. Features 4.5V ~ 23V Input Voltage Range Fixed 3.3V output voltage Supports 8-A continuous output current Integrated 20mQ High side FET and 10m0 low side FET3.3V LDO capable ofsourcing 100mA Internal +1% reference voltage at 25°C Integrated bypass switch, typical Ron is 1.50 Internal 0.6ms soft-start Max switching frequency up to 500kHz fast transient response with COT control mode Power good indicator Ultrasonic Mode Integrated protections for Uv, Ov, OT, and OCP40°C to +150°C operating junction temperature AQFN3X3-12 FC Package Applications Notebook Computers Notebook, Tablet Computers General power supply for 3.3V output

发表了主题帖： ZCC75XXH-40V/150mA高压低功耗线性稳压器替代HT75XX

功能描述  ZCC75XXH是一款高压低功耗线性稳压器，静态电流低至2.5uA，输出电流最大为150mA。该系列产品 采用先进的CMOS工艺和高压PMOSFET，具有快速启动、高输出电压精度等特点。只需要1uF 的陶瓷电容即可保证电压稳定输出, 其内部精密的电压基准和反馈回路，可使电路在输入电压、负载、工艺和温度波动的情况下，确保±1%的输出电压精度。工作温度范围–40°C ~ +125°C，封装形式为SOT89-3 ， SOT23-3L。 特性 • 宽输入电压：2V to 40V • 最大150mA输出电流 • 超低功耗：2.5µA@typ • 超低压差：650mV at 150mA Load @VOUT=5V  • 短路保护电流：60mA  • 优秀的线性/负载特性 • 线性调整率：0.05% typical  • 封装形式：SOT89-3，SOT23-3L ​ 合作洽谈/样品申请：402572194（QQ） 邮箱：gaomaobing@zcc-china.net  

发表了主题帖： ZCC5143-3.5V 至 65V 双路同步降压芯片替代LM5143

Descriptions The ZCC5143 is a 65V synchronous step-down DC/DC controller for high current single or dual outputs. The device features an interleaved, stackable peak current mode control architecture for simple loop compensation, fast transient response, excellent load and line regulation, and precise current sharing through parallel phasing for high output currents. 65ns of ultra-short on-time for the high-side switch facilitates large buck ratios and supports direct buck conversion from 12V, 24V, or 48V automotive inputs to lower voltage rails, reducing system complexity and solution cost. The can continue to operate at nearly 100% duty cycle as needed even when the input voltage drops abruptly to 3.5V. Ultra-high efficiency is achieved by Using an inductor DCR to detect the current, and a shunt resistor can be used to detect it with high accuracy. 15uA no-load quiescent current and regulated output voltage extends the operating runtime of battery-powered systems. The can be powered by the output of a switching regulator or other available power sources. By utilizing the output of a switching regulator or other available power supply to power the , lower input quiescent current and power loss can be achieved.  Features   VIN input voltage range: +3.5V ~ +65V   1% accuracy, 3.3V/5V fixed or 0.6V to 55V adjustable output voltage   Shutdown Mode Current: 4µA (Typ.)   No-load standby current: 15 µA (Typ.)   Dual channel or single output multi-phase  65ns tON(min) for high VIN/VOUT ratio   60ns tOFF(min) for low voltage drop   Hiccup mode over-current protection  VCC, VDDA and Gate Drive UVLO Protection   Thermal shutdown protection with hysteresis  Adaptive Gate Driver Controlled by Voltage Slew Rate   Switching frequency range of 100kHz to 2.2MHz   Optional diode emulation or FPWM   VQFNP6X6-40 package Applications  Automotive Electronic Systems   Advanced Driver Assistance System(ADAS)  Infotainment & Instrumentation Systems

发表了主题帖： ZCC5090EA 替代CS5090EA ,5V升压充电管理芯片

概要 ZCC5090EA是一款5V输入，最大1.5A充电电流，支 持双 节 锂 电 池 串 联 应 用 的 升 压 充 电 管 理 IC 。ZCC5090EA集成功率MOS，采用异步开关架构， 使其在应用时仅需极少的外围器件，可有效减少整体 方案尺寸，降低BOM成本。ZCC5090EA的升压开关 充电转换器的工作频率为500KHz，转换效率为90%。 ZCC5090EA内置四个环路来控制充电过程，分别为 恒流（CC）环路、恒压（CV）环路、芯片温度调节环路、可智能调节充电电流，防止拉垮适配器输出， 并匹配所有适配器的输入自适应环路。 ZCC5090EA集成30V OVP功能，输入端口能够稳定 可靠承受30V以内的耐压冲击，并在输入超过6V时停 止充 电，非 常 适 用 于TY P E - C接 口 的 应 用。同 时 芯 片BAT输出端口耐压30V，极大提高了系统的可靠性。 ZCC5090EA提供了纤小的ESOP8L封装类型供客户 选择，其额定的工作温度范围为-40℃至85℃。 描述 *USB 5V输入异步开关升压充电，集成30V OVP功能 *工作电压3.6~6V，BAT端耐压30V，内部集成高压晶体管 *最大1.5A充电电流，充电电流外部电阻可调 *NTC功能，与使能功能复用 *升压充电效率90% *自动调节输入电流，匹配所有适配器 *支持LED充电状态指示 *500KHz开关频率，内置频率抖动功能 *输出过压，短路保护 *输入过压保护 *IC过温保护，IC温度自适应调节功能 *管脚兼容ZCC5090E  * ESD 2KV 封装 ESOP8L 应用  蓝牙音箱 电子烟 对讲机 POS机  锂电电池包 玩具

发表了主题帖： ZCC75XXH-40V/150mA高压低功耗线性稳压器替代HT75XX

功能描述  ZCC75XXH是一款高压低功耗线性稳压器，静态电流低至2.5uA，输出电流最大为150mA。该系列产品 采用先进的CMOS工艺和高压PMOSFET，具有快速启动、高输出电压精度等特点。只需要1uF 的陶瓷电容即可保证电压稳定输出, 其内部精密的电压基准和反馈回路，可使电路在输入电压、负载、工艺和温度波动的情况下，确保±1%的输出电压精度。工作温度范围–40°C ~ +125°C，封装形式为SOT89-3 ， SOT23-3L。 特性 • 宽输入电压：2V to 40V • 最大150mA输出电流 • 超低功耗：2.5µA@typ • 超低压差：650mV at 150mA Load @VOUT=5V  • 短路保护电流：60mA  • 优秀的线性/负载特性 • 线性调整率：0.05% typical  • 封装形式：SOT89-3，SOT23-3L ​ 合作洽谈/样品申请：402572194（QQ） 邮箱：gaomaobing@zcc-china.net