:kiss: 结贴！

不知道应用程序是否是可以和LM3S8963远程升级的程序分开编译，如分开编译需要调整那些，手册因为没下载到 M3也是才接触 所以 也是慢慢开始看 遇到了问题希望大家能赐教！

tack   EQU     0x00000100 ;******************************************************************************;; <o> Heap Size (in Bytes) <0x0-0xFFFFFFFF:8>;;******************************************************************************Heap    EQU     0x00000000 ;******************************************************************************;; Allocate space for the stack.;;******************************************************************************        AREA    STACK, NOINIT, READWRITE, ALIGN=3StackMem        SPACE   Stack__initial_sp ;******************************************************************************;; Allocate space for the heap.;;******************************************************************************        AREA    HEAP, NOINIT, READWRITE, ALIGN=3__heap_baseHeapMem        SPACE   Heap__heap_limit ;******************************************************************************;; Indicate that the code in this file preserves 8-byte alignment of the stack.;;******************************************************************************        PRESERVE8 ;******************************************************************************;; Place code into the reset code section.;;******************************************************************************        AREA    RESET, CODE, READONLY        THUMB ;******************************************************************************;; The vector table.;;******************************************************************************        EXPORT  __Vectors__Vectors        DCD     StackMem + Stack            ; Top of Stack        DCD     Reset_Handler               ; Reset Handler        DCD     NmiSR                       ; NMI Handler        DCD     FaultISR                    ; Hard Fault Handler        DCD     IntDefaultHandler           ; The MPU fault handler        DCD     IntDefaultHandler           ; The bus fault handler        DCD     IntDefaultHandler           ; The usage fault handler        DCD     0                           ; Reserved        DCD     0                           ; Reserved        DCD     0                           ; Reserved        DCD     0                           ; Reserved        DCD     IntDefaultHandler           ; SVCall handler        DCD     IntDefaultHandler           ; Debug monitor handler        DCD     0                           ; Reserved        DCD     IntDefaultHandler           ; The PendSV handler        DCD     IntDefaultHandler           ; The SysTick handler        DCD     IntDefaultHandler           ; GPIO Port A        DCD     IntDefaultHandler           ; GPIO Port B        DCD     IntDefaultHandler           ; GPIO Port C        DCD     IntDefaultHandler           ; GPIO Port D        DCD     IntDefaultHandler           ; GPIO Port E        DCD     IntDefaultHandler           ; UART0 Rx and Tx        DCD     IntDefaultHandler           ; UART1 Rx and Tx        DCD     IntDefaultHandler           ; SSI0 Rx and Tx        DCD     IntDefaultHandler           ; I2C0 Master and Slave        DCD     IntDefaultHandler           ; PWM Fault        DCD     IntDefaultHandler           ; PWM Generator 0        DCD     IntDefaultHandler           ; PWM Generator 1        DCD     IntDefaultHandler           ; PWM Generator 2        DCD     IntDefaultHandler           ; Quadrature Encoder 0        DCD     IntDefaultHandler           ; ADC Sequence 0        DCD     IntDefaultHandler           ; ADC Sequence 1        DCD     IntDefaultHandler           ; ADC Sequence 2        DCD     IntDefaultHandler           ; ADC Sequence 3        DCD     IntDefaultHandler           ; Watchdog timer        DCD     IntDefaultHandler           ; Timer 0 subtimer A        DCD     IntDefaultHandler           ; Timer 0 subtimer B        DCD     IntDefaultHandler           ; Timer 1 subtimer A        DCD     IntDefaultHandler           ; Timer 1 subtimer B        DCD     IntDefaultHandler           ; Timer 2 subtimer A        DCD     IntDefaultHandler           ; Timer 2 subtimer B        DCD     IntDefaultHandler           ; Analog Comparator 0        DCD     IntDefaultHandler           ; Analog Comparator 1        DCD     IntDefaultHandler           ; Analog Comparator 2        DCD     IntDefaultHandler           ; System Control (PLL, OSC, BO)        DCD     IntDefaultHandler           ; FLASH Control        DCD     IntDefaultHandler           ; GPIO Port F        DCD     IntDefaultHandler           ; GPIO Port G        DCD     IntDefaultHandler           ; GPIO Port H        DCD     IntDefaultHandler           ; UART2 Rx and Tx        DCD     IntDefaultHandler           ; SSI1 Rx and Tx        DCD     IntDefaultHandler           ; Timer 3 subtimer A        DCD     IntDefaultHandler           ; Timer 3 subtimer B        DCD     IntDefaultHandler           ; I2C1 Master and Slave        DCD     IntDefaultHandler           ; Quadrature Encoder 1        DCD     IntDefaultHandler           ; CAN0        DCD     IntDefaultHandler           ; CAN1        DCD     IntDefaultHandler           ; CAN2        DCD     IntDefaultHandler           ; Ethernet        DCD     IntDefaultHandler           ; Hibernate ;******************************************************************************;; This is the code that gets called when the processor first starts execution; following a reset event.;;******************************************************************************        EXPORT  Reset_HandlerReset_Handler        ;        ; Call the C library enty point that handles startup.  This will copy        ; the .data section initializers from flash to SRAM and zero fill the        ; .bss section.        ;        IMPORT  __main        B       __main ;******************************************************************************;; This is the code that gets called when the processor receives a NMI.  This; simply enters an infinite loop, preserving the system state for examination; by a debugger.;;******************************************************************************NmiSR        B       NmiSR ;******************************************************************************;; This is the code that gets called when the processor receives a fault; interrupt.  This simply enters an infinite loop, preserving the system state; for examination by a debugger.;;******************************************************************************FaultISR        B       FaultISR ;******************************************************************************;; This is the code that gets called when the processor receives an unexpected; interrupt.  This simply enters an infinite loop, preserving the system state; for examination by a debugger.;;******************************************************************************IntDefaultHandler        B       IntDefaultHandler ;******************************************************************************;; Make sure the end of this section is aligned.;;******************************************************************************        ALIGN ;******************************************************************************;; Some code in the normal code section for initializing the heap and stack.;;******************************************************************************        AREA    |.text|, CODE, READONLY ;******************************************************************************;; The function expected of the C library startup code for defining the stack; and heap memory locations.  For the C library version of the startup code,; provide this function so that the C library initialization code can find out; the location of the stack and heap.;;******************************************************************************    IF :DEF: __MICROLIB        EXPORT  __initial_sp        EXPORT  __heap_base        EXPORT  __heap_limit    ELSE        IMPORT  __use_two_region_memory        EXPORT  __user_initial_stackheap__user_initial_stackheap        LDR     R0, =HeapMem        LDR     R1, =(StackMem + Stack)        LDR     R2, =(HeapMem + Heap)        LDR     R3, =StackMem        BX      LR    ENDIF ;******************************************************************************;; Make sure the end of this section is aligned.;;******************************************************************************        ALIGN ;******************************************************************************;; Tell the assembler that we're done.;;******************************************************************************        END 这是启动代码 向量要怎么修改

:( :(